[Nonerodible Channels]   [Erodible Channels]   [Tractive Force]   [Permissible Tractive Force]   [Other Features]   [Questions]   [Problems]   [References]     

CHAPTER 6:  CHANNEL DESIGN


6.1  NONERODIBLE CHANNELS

[Erodible Channels]   [Tractive Force]   [Permissible Tractive Force]   [Other Features]   [Questions]   [Problems]   [References]      [Top]  

There are two types of channels: (1) nonerodible, and (2) erodible. Nonerodible channels are typically lined with a hard construction material, such as concrete or stone masonry. Erodible channels are dug on the ground surface and, therefore, directly in contact with the underlying soil. The design of erodible channels is much more complex than that of nonerodible channels.

The design of nonerodible channels begins with the choice of a uniform flow formula (Chapter 5). The following factors are considered in the design of nonerodible channels:

  • Surface roughness

    The surface roughness (boundary friction) is determined by the type and finish of the material lining the channel boundary. Generally, coarser surfaces have higher friction than smoother surfaces (Fig. 6-1).

    Masonry-lined channel

    Fig. 6-1  A masonry-lined channel.

  • Minimum permissible velocity

    All channels carry a certain amount of sediments (sand, silt, clay). Therefore, flow in channels of very mild bottom slope may lead to excessive sediment deposition. Thus, a minimum permissible velocity, i.e., a minimum bottom slope, is needed to avoid clogging.

  • Maximum bottom slope

    All nonerodible channels will have a tendency to develop roll waves if the Vedernikov V > 1 (Chapter 1). To avoid roll waves, the bottom slope must be kept below a maximum value which is a function of the hydraulics of the flow. For instance, Fig. 6-2 shows a series of drops implemented in a channel to reduce the bottom slope.

    Fig. 6-2  Channel drops implemented in a channel to decrease the channel slope,
    La Joya Canal, Arequipa, Peru.

  • Shape of the cross section

    The channel section of maximum conveyance and, therefore, maximum discharge, is that which has the minimum wetted perimeter for a given flow area. This shape of cross section is referred to as the best hydraulic section. The best hydraulic circular section is a semicircle. The best hydraulic trapezoidal section is a half regular hexagon inscribed in a circle (Chow, 1959) (Fig. 6-3). In practice, however, other design considerations are usually more important than that of maximum conveyance.

    Best hydraulic section of trapezoidal shape

    Fig. 6-3  Best hydraulic section of trapezoidal shape.

  • Side slopes

    The side slope is z H : 1 V, wherein z = 0 for a rectangular section and z > 0 for a trapezoidal section, is a design decision that varies with local conditions (Fig. 6-4). Typical side slopes vary from z = 0 to z = 3.

    Channel transition from rectangular to trapezoidal shape

    Fig. 6-4  Channel transition from rectangular to trapezoidal shape.

  • Freeboard

    The freeboard is the vertical depth measured above the design channel depth, up to the total channel depth (Fig. 6-5). It is intended to account for a safety factor and to minimize wave overtopping.

    Freeboard in an open channel

    Fig. 6-5  Freeboard in the San Luis Canal, California.

  • Slide risk reduction

    In hillslope alignments, care should be taken to reduce the risk of local slides, which, depending on their extent, may render the channel inoperable. Some hillslopes are prone to slides, while others are not. A thorough geological/geotechnical site investigation is required to reduce the risk of slides. Figure 6-6 shows a slide-generated breach in the La Cano Canal, Arequipa, Peru, which occurred on November 4, 2010 (see related video).

    Slide-generated breach, La Cano Canal,
							Arequipa, Peru,<br>which on occurred November 4, 2010

    Fig. 6-6  Slide-generated breach, La Cano Canal, Arequipa, Peru,
    which occurred on November 4, 2010.

Channel lining

Channels or canals may be lined with one of several materials, including concrete, stone masonry, steel, cast iron, timber, glass, and plastic. Channel lining reduces boundary friction and minimizes channel maintenance costs. Figure 6-7 shows the Santa Ana river, at Huntington Beach, California, paved with concrete to reduce flood stage and control floods.

Alamar Creek, in Tijuana, 
Baja California, Mexico

Fig. 6-7  Paved Santa Ana river, Huntington Beach, California.

Figure 6-8 shows Alamar Creek, in Tijuana, Mexico, recently lined up with concrete (2013). It is noted that current environmental design practices strongly discourage the lining of natural channels with concrete.

Alamar Creek, in Tijuana, 
Baja California, Mexico

Fig. 6-8  Alamar Creek, Tijuana, Baja California, Mexico.

Minimum permissible velocity

All water carries a certain amount of suspended solids, in the form of sediments that have entrained somewhere upstream and are being transported by the flow. Typical values of suspended load are 200-300 parts per million (or ppm, equivalent, at this range, to mg/L) (Ponce, 1989). The no-slip condition at the channel boundary (i.e., the local longitudinal velocity is zero at the channel boundary) produces shear stresses and results in sediment entrainment. Once entrained, this sediment needs to be transported through the channel; otherwise, it will settle and eventually clog the channel. The minimum velocity to avoid settling/clogging is the minimum permissible velocity.

The evaluation of minimum permissible velocity may be accomplished with the Shields criterion for initiation of motion. This criterion is embodied in the Shields diagram, shown in Fig. 6-9, which relates the dimensionless shear stress τ* with the boundary Reynolds number R*. The solid curve in Fig. 6-9 separates no motion (below the curve) from motion (above the curve).

Shields diagram for initiation of motion

Fig. 6-9  Shields diagram for initiation of motion (American Society of Civil Engineers, 1975).

Minimum Froude number and minimum permissible velocity

The quadratic friction law, Eq. 5-3, is recast here with τo  as the bottom shear stress:

 
τo  =  ρ f V 2
 
(6-1)

The Shields criterion for initiation of motion is:

                 τo
τ* = _____________  ≥  τ*c

          (γs - γ ) ds
(6-2)

in which τ* = dimensionless shear stress, γs = specific weight of sediment particles, γ = specific weight of water, ds = sediment particle diameter, and τ*c = dimensionless critical shear stress.

Figure 6-9 shows the Shields curve, i.e., the variation of dimensionless critical shear stress τ*c with the boundary Reynolds number R*:

            U* ds
R* =  _________
               ν
(6-3)

in which U* = shear velocity = (τo /ρ)1/2 = ( f )1/2 V, and ν = kinematic viscosity.

The Froude number F is:

              V
F = ___________
         (g D )1/2
(6-4)

in which V = mean velocity, D = hydraulic depth, and g = gravitational acceleration.

Replacing Eqs. 6-1 and 6-4 into Eq. 6-2:

             f D F 2
_____________________  ≥  τ*c
    [ (γs / γ ) - 1 ] ds
(6-5)

In most cases of practical interest, the ratio of specific weights of sediment and water γs /γ is equal to 2.65. Therefore, in terms of Froude number, the Shields criterion for initiation of motion reduces to:

             1.65 τ*c (ds / D )
F  ≥  [ __________________ ] 1/2
                         f
(6-6)

For practical applications, a constant value of dimensionless critical shear stress τ*c = 0.04 may be considered. From Fig. 6-9, it is seen that this value encompasses the range:  4 ≤ R* ≤ 60. Therefore:

             0.066 (ds / D )
F  ≥  [ ________________ ] 1/2
                       f
(6-7)

Equation 6-7 is the practical Shields-based Froude criterion for initiation of motion, applicable through a wide range of boundary Reynolds numbers.

As a practical example of the use of Eq. 6-7, assume ds = 0.4 mm, D = 1 m, and a midrange dimensionless Chezy friction factor f = 0.0035 (equivalent to a Darcy-Weisbach friction factor f = 0.028). The application of Eq. 6-7 leads to:

             
F  ≥  0.087
                       
(6-8)

Combining Eqs. 6-4 and 6-7:

             0.066 (g ds)
V  ≥  [ ______________ ] 1/2
                      f
(6-9)

From Eq. 6-9, the minimum permissible velocity for this flow condition is: Vmin = 0.27 m/s.

A somewhat more precise value of minimum Froude number and minimum permissible velocity may be obtained by using the actual value of dimensionless critical shear stress in Eq. 6-7, in lieu of the convenient approximation τ*c = 0.04. This procedure, however, requires an iteration. For this purpose, the following algorithm is suggested:

  1. Assume R*

  2. Using Fig. 6-9, find τ* = τ*c

  3. With τ*, use Eq. 6-2 to solve for τo

  4. Using Eq. 6-1, calculate the shear velocity U* = (τo /ρ)1/2

  5. Using Eq. 6-3, calculate the new value of R*

  6. Stop if the new value of R* is the same as that assumed in Step 1 (within a certain small tolerance), and use the last value of τ*c (calculated in Step 2) in Eq. 6-6;

  7. Otherwise, return to Step 1, using the new value of R* as the assumed value, and repeat the iteration.



 Example 6-1.

Assume the following channel data:  particle diameter ds = 0.4 mm, hydraulic depth D = 1 m, dimensionless Darcy-Weisbach friction factor f = 0.0035, and water temperature T = 20°C. Using the Shields criterion for initiation of motion, calculate the minimum Froude number and minimum permissible velocity.


calculator image 

ONLINE CALCULATION. Using ONLINE SHIELDS VELOCITY, the minimum Froude number is Fmin = 0.081, and the minimum permissible velocity is Vmin = 0.25 m/s. Note that this result is slightly less than that obtained using Eqs. 6-7 and 6-9.


Channel slope

The design channel slope is usually governed by the chosen alignment and prevailing topography. The actual design channel slope may depend on the purpose of the channel. For example, channels used for irrigation and hydropower require small slopes, in order not to lose too much head during conveyance.

Side slopes depend on local soil and construction conditions, usually as steep as practicable. For lined canals, a side slope of 1.5 H : 1 V is recommended as a standard by the U.S. Bureau of Reclamation, for use in most canals.

For lined canals and steep slopes, when the Vedernikov number exceeds 1, the possibility arises for the development of roll waves (Chapter 1).


Freeboard

Freeboard is the vertical distance from the top of the channel to the water surface at the design condition. This distance should be sufficient to prevent waves or fluctuations in the water surface from overflowing the channel sides. This feature becomes important, particularly in the design of elevated flumes, for the flume substructure may be endangered by an overflow (Fig. 6-10).

The Dulzura conduit, in San Diego County, California,
overflowing after heavy rain, on March 5, 2005

Fig. 6-10  The Dulzura conduit, in San Diego County, California,
overflowing after heavy rain, on March 5, 2005.

There is no universally accepted rule for the determination of freeboard. Wind-generated waves or tidal action may induce high waves, which would need to be kept within channel bounds. Freeboards ranging from less than 5% to more than 30% of the design flow depth are in common practice. For smooth, interior, semicircular flumes on tangents, carrying water at velocities no greater than the critical velocity, with a maximum of 8 ft/s (2.4 m/s), experience has indicated that a freeboard of 6% of the flume diameter is appropriate. For flumes on curves, freeboard must be increased to prevent water from sloping over (Chow, 1959). Note that hydraulic design criteria commonly allow for the use of all or part of the freeboard to accomodate the Probable Maximum Flood (Ponce, 1989).

According to the U.S. Bureau of Reclamation, the approximate range of freeboard extends from 1 ft (0.3 m) for small laterals with shallow depths, to 4 ft (1.2 m) in canals up to 3,000 cfs (85 m3/s) or more. The following formula is applicable:

 
Fb  =  ( C y ) 1/2
 
(6-10)

in which Fb = freeboard, in ft; y = depth of water in the canal, in ft; and C = coefficient, varying from C = 1.5 for a canal capacity of 20 cfs (0.57 m3/s) to C = 2.5 for a canal capacity of 3,000 cfs (85 m3/s) or more. Figure 6-11 shows U.S. Bureau of Reclamation recommended height of lining and height of bank, applicable for the design of freeboard.

U.S. Bureau of Reclamation recommended 
height of lining and height of bank

Fig. 6-11  U.S. Bureau of Reclamation recommended height of lining
and height of bank (Chow, 1959).

Section dimensions

The following steps are taken to choose the dimensions of a channel or canal cross section:

  1. Select the design discharge Q

  2. Select the bottom width b

  3. Select the side slope z  [z H : 1 V] (Fig. 6-12)

    Definition sketch for bottom width <i>b</i> and side slope <I>z</i>.

    Fig. 6-12  Definition sketch for bottom width b and side slope z.

  4. Select the bottom slope S

  5. Estimate the value of Manning's n (Chapter 5:  Manning's n)

  6. Using Q, b, z, S, and n [Steps 1 to 5], compute the normal depth yn, normal velocity vn, and normal Froude number Fn (Chapter 5:  Computation)

  7. Check to see if the normal velocity vn and normal Froude number Fn are large enough to avoid clogging of the canal with sediment (see Minimum permissible velocity in this Chapter)

  8. Select an appropriate freeboard Fb .

Figure 6-13 shows U.S. Bureau of Reclamation recommended bottom width and water depth of lined channels.


U.S. Bureau of Reclamation recommended 
bottom width and water depth of lined channels

Fig. 6-13  U.S. Bureau of Reclamation recommended bottom width and water depth
of lined channels (Chow, 1959).

 Example 6-2.

Design a channel for the following flow conditions: Q = 10 m3/s; b = 5 m; z = 2; S = 0.0016; n = 0.025.


Using Eq. 5-55, by iteration, the normal depth is yn = 1.049 m and the normal velocity is vn = 1.342 m/s. The Froude number based on normal depth is Fn = 0.418. The calculated Froude number is shown to be much larger than 0.087 (Eq. 6-8), the minimum value required to avoid sediment deposition. A freeboard Fb = 0.6 m is assumed.

calculator image 

ONLINE CALCULATION. Using the ONLINECHANNEL01 calculator, the normal depth is yn = 1.049 m; the normal velocity is vn = 1.342 m/s; the Froude number (based on hydraulic depth D = 0.81 m) is: Fn = 0.476.

Note that the true Froude number is that based on hydraulic depth (Eq. 4-6). For a hydraulically wide channel, for which DR, both Froude numbers are approximately the same.


Figure 6-14 shows a major canal built in 1993 in Ceara, Brazil, for the purpose of mitigating a regional drought. The hydraulic characteristics are: Q = 8.32 m3/s, b = 5 m, z = 1.5, S = 0.00005, and n = 0.015. Using the ONLINECHANNEL01 calculator, the normal depth is yn = 1.915 m, the normal velocity is vn = 0.552 m/s, and the Froude number is Fn = 0.149.

Canal do Trabalhador (The Workers' Channel), Ceara, Brazil
Cogerh

Fig. 6-14  The Workers' Channel (Canal do Trabalhador), Ceara, Brazil (1993).


6.2  ERODIBLE CHANNELS

[Tractive Force]   [Permissible Tractive Force]   [Other Features]   [Questions]   [Problems]   [References]      [Top]   [Nonerodible Channels]  

The design of an erodible channel is much more complex than that of a nonerodible channel. The long-term stability of the channel boundary depends on the properties of the material lining the boundary (sand, silt, clay, and combinations thereof), and of the properties of the sediment being transported by the flow. Changes in water and sediment discharge result in cross-sectional changes, either channel depth, channel width, or both.

The stability of the channel boundary is normally assessed in terms of two criteria:

  1. Maximum permissible velocity, and

  2. Maximum permissible tractive stress.

Given Eq. 6-1, these two methods are related as follows:

 
τo max  =  ρ f (Vmax )2
 
(6-11)

 Example 6-3.

Calculate the maximum permissible velocity corresponding to a maximum permissible tractive stress of 20 N/m2. Assume f = 0.0035, i.e., Darcy-Weisbach f = 0.028.


Using Eq. 6-11:

Vmax = [τo max / (ρ f ) ] 1/2 = [ 20 N/m2 / (1000 N s2/m4 × 0.0035 ) ] 1/2 = 2.39 m/s.

 Example 6-4.

Calculate the maximum permissible velocity corresponding to a maximum permissible tractive stress of 0.1 lb/ft2. Assume f = 0.005, i.e., Darcy-Weisbach f = 0.04.


Using Eq. 6-11:

Vmax = [τo max / (ρ f ) ] 1/2 = [ 0.1 lb/ft2 / (1.94 lbs-s2/ft4 × 0.005 ) ] 1/2 = 3.21 ft/s.


Vegetative channels

Table 6-1 shows typical values of maximum permissible tractive stress for various types of vegetative channel linings.

Table 6-1  Typical values of maximum permissible tractive stress.
Channel lining Maximum permissible
tractive stress
(N/m2) (lb/ft2)
Lawn (short-time loaded) 20-30 0.42-0.63
Lawn (long-time loaded) 15-18 0.31-0.38
Fascine sausage 60-70 1.25-1.46
Fascine roll 100-150 2.09-3.13
Weighted fascine 60-100 1.25-2.09
Brush mattress 150-300 3.13-6.26
Live staking in rip rap > 140 > 2.92
Willows/alder 80-140 1.67-2.92
Gabions 80-140 1.67-2.92

Figure 6-15 shows details of the design of a channel lining using a brush mattress.

Design of brush mattress:  Top view

Fig. 6-15 (a)  Design of brush mattress:  Top view.

Design of brush mattress:  Side view

Fig. 6-15 (b)  Design of brush mattress:  Side view.

Design of brush mattress:  Side view after a few months

Fig. 6-15 (c)  Design of brush mattress:  Side view after a few months.

Design of brush mattress:  View after project completion

Fig. 6-15 (d)  Design of brush mattress:  View after project completion.

Figure 6-16 shows details of a channel lining using live staking in riprap.

Live staking:  Schematic

Fig. 6-16 (a)  Live staking:  Schematic.

Live staking:  Soon after installation

Fig. 6-16 (b)  Live staking:  Soon after installation.

Live staking:  Sometime after installation

Fig. 6-16 (c)  Live staking:  Sometime after installation.

Live staking:  2-5 years after installation

Fig. 6-16 (d)  Live staking:  2-5 years after installation.

Live staking:  Established project.

Fig. 6-16 (e)  Live staking:  Established project.

Gabion-lined channels

A gabion system is wire-enclosed riprap consisting of mats or baskets fabricated with wire mesh, filled with small riprap, and anchored to a slope (Fig. 6-17). Wrapping the riprap enables the use of smaller stone sizes for the same resistance to displacement by water energy. This is a particular advantage when constructing rock lining in areas of difficult access. The wire basket also allows steeper (up to vertical) channel linings to be constructed from commercially available wire units or from wire-fencing material.

Placement of gabion mattress.
Unknown

Fig. 6-17  Placement of gabion mattress.

Gabion systems provide an effective way to control erosion in streams, rivers and canals. They are normally designed to sustain large channel velocities [5 m/s (15 ft/s) or higher]. Gabions are constructed by individual units that vary in length from 2 m (6 ft) to nearly 30 m (100 ft); therefore, applications can range anywhere from small ditches to large canals (Fig. 6-18).

Dimensions of gabions boxes and mattresses.
Unknown

Fig. 6-18  Dimensions of gabions boxes and mattresses.

Gabion channels are a compromise between riprap and concrete channels. When the same-size rocks are used in gabions and riprap, the acceptable velocity for gabions is three to four times that of riprap. Unlike concrete, gabions can be vegetated to blend into the natural landscape (Fig. 6-19).

Gabion channels with vegetation have the following advantages:

  • Allow infiltration and exfiltration

  • Filter out contaminants

  • More flexible than paved channels

  • Provide greater energy dissipation than concrete channels

  • Improve habitat for flora and fauna

  • More aesthetically pleasing

  • Lower cost to install, although some maintenance is required.

Values of Manning's n for gabion-lined channels are normally in the range 0.025 ≤ n ≤ 0.030.


Live staking:  Established project.

Fig. 6-19  Established channel lining with gabions.


6.3  TRACTIVE FORCE

[Permissible Tractive Force]   [Other Features]   [Questions]   [Problems]   [References]      [Top]   [Nonerodible Channels]   [Erodible Channels]  

The tractive force is the summation of the (tractive) shear stresses over (an area of) the channel boundary. Under equilibrium conditions, to develop the tractive stress equation, the acting gravitational force is made equal to the resisting frictional force. The gravitational force is (Fig. 6-20):

 
W sin θ  ≅  W tan θ  =  WHx )
 
(6-12)

in which W = weight of the control volume of area A and length Δx, ΔH = drop within the control volume, and θ = channel bottom slope.

Definition sketch for the derivation of the tractive force equation

Fig. 6-20  Definition sketch for derivation of the tractive force equation.

Since S = ΔHx, it follows that the acting gravitational force is:

 
Fg  =  γ A Δx S
 
(6-13)

The resisting frictional force is:

 
Ff  =  τo P Δx
 
(6-14)

in which τo = bottom shear stress, and P = wetted perimeter.

Equating gravitational and frictional forces:

 
τo  =  γ R S
 
(6-15)

in which R = A /P = hydraulic radius.

For hydraulically wide channels, for which RDy,

 
τo  =  γ y S
 
(6-16)

The tractive stress varies along the wetted perimeter, reaching a peak value along the middle of the channel. Figure 6-21 shows a typical variation for a trapezoidal cross section, in which b/y = 4 and z = 1.5.

Variation of tractive stress in a trapezoidal channel section

Fig. 6-21  Variation of tractive stress in a trapezoidal channel, with b/y = 4 and z = 1.5 (Chow, 1959).

At the bottom center, the tractive stress approaches asymptotically its full (maximum) value: τb = γyS , as shown in Fig. 6-22. Along the channel sides, the tractive stress approaches asymptotically a fraction of the full value: τs = 0.78 γyS , as shown in Fig. 6-23.

Variation
 of maximum tractive stress on channel bottom with aspect ratio <i>b</i>/<i>y</i>,

Fig. 6-22  Variation of maximum tractive stress on channel bottom
with aspect ratio b/y (Chow, 1959).

Variation 
of maximum tractive stress on channel sides with aspect ratio <i>b</i>/<i>y</i>

Fig. 6-23  Variation of maximum tractive stress on channel sides
with aspect ratio b/y (Chow, 1959).

Tractive force ratio

Figure 6-24 shows three particles on the channel boundary, one on the left side, another on the right side, and the third one on level ground (bottom). The tractive force ratio K is defined as:

           a τs            τs
K  =  _______  =  ______
           a τL            τL
(6-17)

in which a = effective area of the particle, τs = shear stress on the side, and τL = shear stress on level ground.

Variation
 of maximum tractive stress on channel bottom with aspect ratio <i>b</i>/<i>y</i>,

Fig. 6-24  Definition sketch for the forces acting on a particle resting on the surface
of a channel bed (Chow, 1959).

Define θ as the angle of repose of the material forming the channel boundary (note that θ is not shown explicitly in Fig. 6-24). The ratio K is a function of the channel side slope φ and of the angle of repose θ of the material. To derive K, consider the two forces that are acting on a particle of submerged weight Ws resting on the side of the channel, with tractive stress τs:

  1. The tractive force:  aτs

  2. The gravitational force component along the side:  Ws sin φ

The resultant force acting along the side plane is:

 
Fa  =  (Ws2 sin2φ  +  a2τs2)1/2
 
(6-18)

At equilibrium, the resisting force is equal to the acting force. From solid mechanics, the resisting force is equal to the normal force (Ws cosφ ) times the coefficient of friction (tanθ ):

 
Fr  =  Ws  cosφ  tanθ
 
(6-19)

Therefore:

 
Ws  cosφ  tanθ  =  (Ws2 sin2φ  +  a2τs2)1/2
 
(6-20)

Squaring both sides:

 
Ws2 cos2φ  tan2θ  =  Ws2 sin2φ  +  a2τs2
 
(6-21)

 
a2τs2  =  Ws2 cos2φ  tan2θ  -  Ws2 sin2φ
 
(6-22)

 
τs2  =  (Ws /a)2 cos2φ  tan2θ  -  (Ws /a)2 sin2φ
 
(6-23)

                                                           tan2φ
τs2  =  (Ws /a)2 cos2φ  tan2θ  [ 1  -  _________ ]
                                                           tan2θ
(6-24)

                                                     tan2φ
τs  =  (Ws /a) cosφ  tanθ  [ 1  -  _________ ] 1/2
                                                     tan2θ
(6-25)

Equation 6-25 is the shear stress on the side of a channel with side slope angle φ and repose angle θ. For a level surface, with φ = 0: sinφ = 0 and cosφ = 1. Thus, the force balance of Eq. 6-20 reduces to:

 
Ws  tanθ  =  aτL
 
(6-26)

Therefore, the shear stress that causes impending motion on a level surface is:

 
τL  =  (Ws /a) tanθ
 
(6-27)

Combining Eqs. 6-17, 6-25, and 6-27, the tractive force ratio is:

                               tan2φ
K  =  cosφ  [ 1  -  _________ ] 1/2
                               tan2θ
(6-28)

It is seen that K is only a function of φ and θ. Equation 6-28 is equivalent to (See box below):

                      sin2φ
K  =   [ 1  -  __________ ] 1/2
                      sin2θ
(6-29)


Derivation of Eq. 6-29

Equation 6-28 is simplified by resorting to established trigonometric identities:

                               tan2φ
K  =  cosφ  [ 1  -  _________ ] 1/2
                               tan2θ
(6-28a)

                              cos2φ  tan2φ
K  =   [ cos2φ  -  ________________ ] 1/2
                                   tan2θ
(6-28b)

                              sin2φ
K  =   [ cos2φ  -  _________ ] 1/2
                              tan2θ
(6-28c)

                              sin2φ  cos2θ
K  =   [ cos2φ  -  ________________ ] 1/2
                                   sin2θ
(6-28d)

                                  sin2φ  (1 - sin2θ)
K  =   [ 1 - sin2φ  -  _____________________ ] 1/2
                                           sin2θ
(6-28e)

                      sin2φ
K  =   [ 1  -  __________ ] 1/2
                      sin2θ
(6-29)



Angle of repose

Figure 6-25 shows the angle of repose of noncohesive materials, i.e., the angle θ in Eq. 6-29. The particle size (in inches) is that for which 25% of the material, by weight, is larger.

Variation
 of maximum tractive stress on channel bottom with aspect ratio <i>b</i>/<i>y</i>

Fig. 6-25  Angle of repose of noncohesive materials (Chow, 1959).


6.4  PERMISSIBLE TRACTIVE FORCE

[Other Features]   [Questions]   [Problems]   [References]      [Top]   [Nonerodible Channels]   [Erodible Channels]   [Tractive Force]  

The permissible tractive force (unit force, or stress) method is used in the design of erodible channels and canals. The permissible unit tractive force is the maximum shear stress that will not cause erosion of the material forming the channel bed on a level surface. The value, obtained from laboratory experiments, is referred to as the critical unit tractive force, or critical shear stress.

Figure 6-26 shows permissible unit tractive force (unit tractive stress) for canals in noncohesive materials. The figure applies through a range of (average) particle diameter from 0.1 to 100 mm. The left side of the graph applies for fine noncohesive material (sand), with diameter ranging from 0.1 to 5 mm. Three curves are shown:

  1. The upper curve, applicable for canals with high content of fine sediment (silt) in the water;

  2. The middle curve, applicable for canals with low content of fine sediment (silt) in the water;

  3. The lower curve, applicable for canals with clear water.

Note that the cleaner the water, the more likely it is to pick up sediment from the boundary and, therefore, the lower the value of the permissible unit tractive force.

The right side of Fig. 6-26 applies for canals in coarse noncohesive material, with diameter ranging from 5 to 100 mm (fine to very coarse gravel, to small cobbles). The line shown in Fig. 6-26 is equal to 0.4 times the particle diameter (in inches) for which 25% of the material is larger, by weight, i.e., the permissible unit tractive force, or permissible tractive stress, is equal to 0.4 × d25 (in).

Permissible unit tractive forces for canals in 
noncohesive materials

Fig. 6-26  Permissible unit tractive force for canals in noncohesive materials (Chow, 1959).

For cohesive materials, the critical shear stress is a function of the type of soil (sandy clays to lean clays) and the voids ratio, as shown in Fig. 6-27.

Permissible unit tractive forces for canals in 
cohesive materials

Fig. 6-27  Permissible unit tractive force for canals in cohesive materials (Chow, 1959).

The values of Figs. 6-26 and 6-27 are applicable to straight channels. For sinuous channels, the values shown in the figures should be reduced to account for bank scour. Table 6-2 shows recommended percentage reduction in critical shear stress to account for channel sinuosity.

Table 6-2  Reduction in critical shear stress
to account for channel sinuosity.
Sinuosity Reduction
(%)
Low 10
Moderate 25
High 40

Permissible tractive force method

The permissible tractive force method is a method to design erodible channels based on the estimated critical shear stress for the material(s) forming the channel boundary. The value of critical shear stress is determined experimentally or from established experience. The computational procedure is described below, along with a worked example, for two possible cases:

  • Use of the same material on sides and bottom, and

  • Use of one material on the sides and another on the bottom.

A. The same material on sides and bottom

Input data:  Discharge Q, side slope z, channel slope S, and Manning's n; particle d25 and grain shape; material on sides and bottom are the same.


  1. Assume b/y = 6, i.e., a reasonable value to start.

  2. Assume that the tractive force on the sides is controlling the design. This is the usually case when the material on the sides and bottom are the same.

  3. With b/y and z, enter Fig. 6-23 to determine the value of Cs (Cs is the ordinate of Fig. 6-23) on the expression for the acting unit tractive force on the sides: Ts = Cs γ y S.

  4. With d25 and grain shape, use Fig. 6-25 to find the angle of repose θ.

  5. Calculate side slope: φ = tan-1 (1/z)

  6. Use Eq. 6-29 to calculate K.

  7. Use Fig. 6-26 to determine the permissible unit tractive force on level ground τL.

  8. Calculate the permissible unit tractive force on the sides: τs = K τL.

  9. Set the permissible unit tractive force greater than or equal to the acting unit tractive force: τsTs; i.e., τsCs γ y S

  10. Solve for flow depth: y = τs / (Cs γ S)

  11. Calculate b: b = (b/y) y

  12. With Q, b, z, n, and S known, solve for normal depth yn.


  13. Test to confirm that yny. If not, assumed value of b/y is too small. Assume a larger value and return to Step 11 and iterate. Once satisfied, set y = yn and go to next step.

  14. With last b/y and z, enter Fig. 6-22 to determine the value of Cb (the ordinate of Fig. 6-22) on the expression for the acting unit tractive force on level ground TL = Cb γ y S.

  15. Calculate TL = Cb γ yn S

  16. Compare TL calculated in Step 15 with τL calculated in Step 7.

  17. If TLτL, the sides control the design, as initially assumed. Stop here.



A. Worked example

Input data:  Q = 600 cfs; z = 2, channel slope S = 0.001, and Manning's n = 0.022; particle d25 = 0.7 in, and slightly angular grain shape; material on sides and bottom are the same.


  1. Assume b/y = 6.


  2. Assume that the tractive force on the sides is controlling the design.


  3. With b/y = 6 and z = 2, enter Fig. 6-23 to determine the value of Cs = 0.78.


  4. With d25 = 0.7 in and slightly angular grain shape, use Fig. 6-25 to find θ = 34°.

  5. φ = tan-1 (1/z) = 26.565°

  6. Use Eq. 6-29 to calculate K = 0.6.

  7. Use d25 = 0.7 inches in Fig. 6-26 to determine τL = 0.28 lb/ft2.

  8. τs = K τL = 0.6 × 0.28 = 0.168 lb/ft2.

  9. Set the permissible unit tractive force greater than or equal to the acting unit tractive force: τs = 0.168 ≥ Cs γ y S = (0.78) (62.4) y (0.001)

  10. Solve for flow depth: y ≤ 3.45 ft. Set y = 3.45 as the target flow depth.

  11. b = (6) (3.45) = 20.7. Round to b = 21 ft.

  12. With Q = 600, b = 21, z = 2, n = 0.022, and S = 0.001, solve for normal depth: yn = 4.536 ft.

  13. yn = 4.536 > y = 3.45. The width b is too short. Assume (by trial and error) b/y = 10. b = (10) (3.45) = 34.5. Round to b = 35 ft. With new b, solve for normal depth: yn = 3.376 ft. Now yn < y. Set y = 3.376 ft and go to next step.

  14. With b/y = 10 and z = 2, enter Fig. 6-22 to determine the value of Cb = 1.0.

  15. Calculate TL = (1.0) (62.4) (3.376) (0.001) = 0.211 lb/ft2.

  16. Compare TL = 0.211 calculated in Step 15 with τL = 0.28 calculated in Step 7.

  17. TL = 0.211 < τL = 0.28; therefore, the sides control the design, as initially assumed. Stop here.


B. One material on the sides and another on the bottom

Input data:  Discharge Q, side slope z, channel slope S, and Manning's n; material on sides and bottom are different, specify type of material, particle size and grain shape, and fine sediment content if required.


  1. Assume b/y = 6, i.e., a reasonable value to start.

  2. Assume that the tractive force on the sides is controlling the design. This is the usually case when the material on the sides and bottom are the same.

  3. With b/y and z, enter Fig. 6-23 to determine the value of Cs (Cs is the ordinate of Fig. 6-23) on the expression for the acting unit tractive force on the sides: Ts = Cs γ y S.

  4. With d25 and grain shape, use Fig. 6-25 to find the angle of repose θ.

  5. Calculate side slope: φ = tan-1 (1/z)

  6. Use Eq. 6-29 to calculate K.

  7. Use Fig. 6-26 to determine the permissible unit tractive force on level ground based on the material from the sides τLs (right of Fig. 6-26), and the permissible unit tractive force on level ground based on the material from the bottom τLb (left of Fig. 6-26)

  8. Calculate the permissible unit tractive force on the sides: τs = K τLs.

  9. Set the permissible unit tractive force greater than or equal to the acting unit tractive force: τsTs; i.e., τsCs γ y S

  10. Solve for flow depth: y = τs / (Cs γ S)

  11. Calculate b: b = (b/y) y

  12. With Q, b, z, n, and S known, solve for normal depth yn.

  13. Test to confirm that yny. If not, assumed value of b/y is too small. Assume a larger value and return to Step 11 and iterate. Once satisfied, set y = yn and go to next step.

  14. With last b/y and z, enter Fig. 6-22 to determine the value of Cb (the ordinate of Fig. 6-22) on the expression for the acting unit tractive force on level ground TL = Cb γ y S.

  15. Calculate TL = Cb γ yn S

  16. Compare TL calculated in Step 15 with τLb calculated in Step 7.

  17. If TLτL, the sides control the design, as initially assumed. Instead, if TL > τL, the bottom controls the design.

  18. If TL > τL, force TL = τL.




  19. Solve for new y, confirming bottom control.


B. Worked example

Input data:  Q = 600 cfs; z = 2, channel slope S = 0.001, and Manning's n = 0.022; material on the sides: noncohesive, d25 = 0.7 in, slightly angular grain shape; material on the bottom: noncohesive, d60 = 0.8 mm, with high content of fine sediment in the water.


  1. Assume b/y = 6.


  2. Assume that the tractive force on the sides is controlling the design.


  3. With b/y = 6 and z = 2, enter Fig. 6-23 to determine the value of Cs = 0.78.


  4. With d25 = 0.7 in and slightly angular grain shape, use Fig. 6-25 to find θ = 34°.

  5. φ = tan-1 (1/z) = 26.565°

  6. Use Eq. 6-29 to calculate K = 0.6.

  7. Use Fig. 6-26 (right) to determine τLs = 0.28 lb/ft2; use Fig. 6-26 (left) to determine τLb = 0.09 lb/ft2.


  8. τs = K τLs = 0.6 × 0.28 = 0.168 lb/ft2.

  9. Set the permissible unit tractive force greater than or equal to the acting unit tractive force: τs = 0.168 ≥ Cs γ y S = (0.78) (62.4) y (0.001)

  10. Solve for flow depth: y ≤ 3.45 ft.

  11. b = (6) (3.45) = 20.7. Round to b = 21 ft.

  12. With Q = 600, b = 21, z = 2, n = 0.022, and S = 0.001, solve for normal depth: yn = 4.536 ft.

  13. yn = 4.536 > y = 3.45. The width b is too short. Assume (by trial and error) b/y = 10. b = (10) (3.45) = 34.5. Round to b = 35 ft. With new b, solve for normal depth: yn = 3.376 ft. Now yn < y. Set y = 3.376 ft and go to next step.

  14. With b/y = 10 and z = 2, enter Fig. 6-22 to determine the value of Cb = 1.0.

  15. Calculate TL = (1.0) (62.4) (3.376) (0.001) = 0.211 lb/ft2.

  16. Compare TL = 0.211 calculated in Step 15 with τLb = 0.09 calculated in Step 7.

  17. TL = 0.211 > τL = 0.09; therefore, the bottom controls the design.

  18. Force TL = Cb γ yn S = (1.0) (62.4) y (0.001) = 0.09. Therefore: y = 1.44 ft. Assume (by trial and error) b/y = 106. Therefore: b = 154 ft.

  19. With Q = 600, b = 152, z = 2, S = 0.001, and n = 0.022, calculate y = 1.44 ft. Design now OK!



6.5  OTHER FEATURES

[Questions]   [Problems]   [References]      [Top]   [Nonerodible Channels]   [Erodible Channels]   [Tractive Force]   [Permissible Tractive Force]  

Other features in hydraulic channel design include canal drops and creek crossings, dissipation structures, and grade control structures. Figures 6-28 to 6-34 show some illustrative examples.

A series of canal drops
for the purpose of controlling flow instability

Fig. 6-28  A series of canal drops for the purpose of controlling flow instability,
Cabana-Maņazo irrigation project, Puno, Peru.

Crossing of Tinajones feeder canal throughChiriquipe Creek, Lambayeque, Peru

Fig. 6-29  Crossing of Tinajones feeder canal through Chiriquipe Creek, Lambayeque, Peru.

A small creek bypass to the 
							 Wellton-Mohawk Canal

Fig. 6-30  A small creek bypass, Wellton-Mohawk Canal, Wellton, Arizona.

A canal crossing a stream by means
of a siphon

Fig. 6-31  A canal crossing a stream by means of a siphon,
Cabana-Maņazo irrigation project, Puno, Peru.

Crossing between an irrigation and drainage canal, Region 1, Guyana.

Fig. 6-32  Crossing between an irrigation and a drainage canal (top), Region 1, Guyana.

A canal crossing a stream by means
of a siphon All American canal

Fig. 6-33  Crossing of the New River by the All-American Canal by means
of a large siphon, near Calexico, Imperial valley, California.

Dissipation structure, Mashcon river,
							 Cajamarca, Peru.

Fig. 6-34  Dissipation structure, Mashcon river, Cajamarca, Peru.

Grade control structure, Caqueza river,
							 Cundinamarca, Colombia.

Fig. 6-35  Grade control structure, Caqueza river, Cundinamarca, Colombia.


QUESTIONS

[Problems]   [References]      [Top]   [Nonerodible Channels]   [Erodible Channels]   [Tractive Force]   [Permissible Tractive Force]   [Other Features]  

  1. What determines the surface roughness in an artificial canal?

  2. What is the freeboard in the design of a canal?

  3. What is the abscissa in the Shields diagram?

  4. What is the ordinate in the Shields diagram?

  5. What Froude number will generally assure initiation of motion?

  6. How are the minimum and maximum permissible velocities reconciled in a channel design?

  7. How are the maximum permissible velocities and shear stresses related?

  8. What is the maximum value of the coeeficient Cs for shear stress on the channel sides?

  9. What is the range of angle of repose of noncohesive materials?

  10. What is the tractive force ratio?

  11. How does the content of fine sediment in the water affect the value of permissible unit tractive force?

  12. When is a grade control structure justified?


PROBLEMS

[References]      [Top]   [Nonerodible Channels]   [Erodible Channels]   [Tractive Force]   [Permissible Tractive Force]   [Other Features]   [Questions]  

  1. What is the minimum permissible velocity for a sediment particle diameter ds = 0.6 mm and a dimensionless Chezy (modified Darcy-Weisbach) friction factor f = 0.004?

  2. What is the minimum Froude number and minimum permissible velocity for a sediment particle diameter ds = 0.6 mm, dimensionless Chezy friction factor f = 0.004, hydraulic depth D = 1 m, and water temperature T = 20°C?

  3. What is the minimum Froude number and minimum permissible velocity for a sediment particle diameter ds = 0.3 mm, dimensionless Chezy friction factor f = 0.003, hydraulic depth D = 3 ft, and water temperature T = 68°F?

  4. A channel has the following data:   Q = 330 cfs, z = 2, n = 0.025, and S = 0.0018. Use the tractive force method to calculate the bottom width and depth under the following conditions:

    • The particles are the same in sides and bottom; they are moderately angular and of size d25 = 0.9 in.

    • Same as in (a), but the particles are moderately rounded.

    Discuss how the particle shape affects the design. Verify with ONLINE TRACTIVE FORCE.

  5. A channel has the following data:   Q = 220 m3/s, z = 2, n = 0.03, and S = 0.0006. Use the tractive force method to calculate the bottom width and depth under the following conditions:

    • The particles on the sides are slightly angular and of size d25 = 35 mm; the particles on the bottom are of size d50 = 5 mm.

    • The particles on the sides are the same as in (a), but the particles on the bottom are smaller, of size d50 = 4 mm.

    Both cases (a) and (b) have low content of fine sediment in the water and the channel sinuosity is negligible. Discuss how the bottom particle size affects the design. Verify with ONLINE TRACTIVE FORCE.

  6. A certain type of lawn has a critical shear stress τc = 30 N/m2. The dimensionless Chezy friction factor f = 0.0075. What is a good estimate of the critical velocity?


REFERENCES

   [Top]   [Nonerodible Channels]   [Erodible Channels]   [Tractive Force]   [Permissible Tractive Force]   [Other Features]   [Questions]   [Problems]  

American Society of Civil Engineers, 1975. Sedimentation Engineering. Manual of Practice No. 54.

Chow, V. T. 1959. Open-channel Hydraulics. McGraw Hill, New York.

Ponce, V. M. 1989. Engineering Hydrology, Principles and Practices. Prentice Hall, Englewood Cliffs, New Jersey.


http://openchannelhydraulics.sdsu.edu
201007 08:30

Documents in Portable Document Format (PDF) require Adobe Acrobat Reader 5.0 or higher to view; download Adobe Acrobat Reader.